NEW / / power generation diesel hfo / C175-16 (50 Hz)
C175-16 (50 Hz) power generation diesel hf
C175-16 (50 Hz)
SPECIFICATIONS
EQUIPMENT
RELATED PRODUCTS
C175-16 (50 Hz)
power generation diesel hfo
- Height Maximum 3307 mm130.2 in
- Length Maximum 7900 mm311 in
- Width Maximum 2756 mm108.5 in
SPECIFICATIONS
- Height Maximum 3307 mm130.2 in
- Length Maximum 7900 mm311 in
- Width Maximum 2756 mm108.5 in
- Minimum Rating 2500 kVA
- Maximum Rating 3100 kVA
- Voltage 220 - 13800 Volts
- Frequency 50 Hz
- Speed 1500 RPM
- Emissions Fuel Strategy Low Fuel Consumption, U.S. EPA Certified for Stationary Emergency Use Only (Tier 2 Nonroad Equivalent Emission Standards)
- Engine Model C175-16 SCAC, V-16, 4-Stroke Water-Cooled Diesel
- Aspiration Turbo Aftercooled
- Governor Type ADEM™ A4
- Fuel System Common Rail
- Bore 175 mm8.89 in
- Displacement 84.67 l5155.88 in³
- Stroke 220 mm8.66 in
- Compression Ratio 50 Hz 16:07:01
- Compression Ratio 60 Hz 15:03:01
- Industry power-generation-diesel-hfo
EQUIPMENT
C175-16 (50 Hz) Standard Equipment
- Air Inlet System
- 4 x Single element canister with service indicator(s)
- Control Panel
- EMCP4 / EMCP4.2
- Emergency stop pushbutton
- 24 Volt DC operation
- Environmental sealed front face.
- Text alarm / event descriptions.
- Generator mounted - rear facing
- Controls
- Speed adjust
- Auto / start / stop control.
- Engine cool-down timer.
- Engine cycle crank
- Alarm acknowledge
- Lamp test
- True RMS AC metering, 3-phase, +/-2% accuracy
- Digital Indicators
- RPM
- DC Volts
- Operating hours
- Oil pressure (psi, kPa or bar)
- Coolant temperature
- Volts (L-L & L-N)
- Frequency (Hz)
- Amps (per phase & average)
- Power Factor (per phase & average)
- Warning / shutdown Indicators
- Low oil pressure
- High coolant temperature
- Overspeed
- Emergency stop
- Failure to start (overcrank)
- Low coolant temperature
- Low coolant level
- Programmable Protective Relaying Functions
- Generator phase sequence
- Over / under voltage
- Over / under frequency
- Reverse power
- Reverse Reactive Power
- Overcurrent
- Communications
- Customer data link (Modbus RTU)
- Accessory module data link
- Serial annunciator module data link
- 6 Programmable digital inputs
- 4 Programmable relay outputs (Form A)
- 2 Programmable relay outputs (Form C)
- 2 Programmable digital outputs
- Cooling System
- SCAC cooling
- Radiator group - shipped loose
- Fan and belt guards
- Coolant drain line and valves
- Coolant Sensors
- Exhaust System
- Dry Exhaust Manifold
- Bolted flange, with bellow for each turbo
- Fuel System
- Primary fuel filter water / fuel water separator
- 10 Micron Spin On Type
- Filters x 3
- Secondary / Tertiary fuel filters
- 4 Micron Spin On Type
- Engine mounted filters X3
- Generator and Attachments
- 3 Phase Brushless
- Salient pole
- 6 Leads
- IEC Platinum stator RTDs
- Voltage Regulator
- Voltage regulator
- Reactive droop capability
- 3 Phase voltage sensing
- RFI suppression
- Min / max exciter limiter
- exciter diode monitor
- Form Wound
- Permanent magnet
- NEMA Class H insulation
- Class H temperature rise at 40C ambient
- (LV) Busbar connections, top/center mounted, top cable entry
- 50 Hz models: IEC standard hole pattern
- (MV) Busbar connections, right side extension box, bottom cable entry
- Anti condensation space heater
- Class F temperature rise at 40C ambient
- Right side extension box, bottom cable entry
- Governing System
- ADEM A4
- Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
- Lube System
- Lubricating oil
- Gear type lube oil pump
- Integral lube oil cooler
- Oil filter, filler and dipstick
- Oil drain lines and valve
- Fumes disposal
- Prelube - required with prime, continuous, and standby
- Mounting Systems
- Rails - Engine / generator
- Rubber anti-vibration mounts (shipped loose)
- Dual 24 volt electric starting motors
- Batteries and battery rack w/cables
- Battery disconnect switch
- General
- Paint - Caterpillar yellow with high gloss black rails & radiator
- Right hand service
- Flywheel and flywheel housing-SAE No. 00
- SAE standard rotation
C175-16 (50 Hz) Optional Equipment
- Air Inlet System
- Single element air cleaner
- Dual element air cleaner
- Air inlet adapters
- Air inlet protection
- Control Panel
- EMCP 4.3, EMCP 4.4
- EMCP 4.4 optional harness
- EMCP and MV&HV power connection locations
- Load share module
- EMCP mounting location - LV / MV
- Customer AC-DC connection mounting location - LV/MV
- Load share module / auxiliary plate and auxiliary box (LV)
- Load share governor
- Frame boxes
- Automatically selected ground
- EMCP voltage and current sensing groups
- Raise lower switch
- Speed adjust
- Annunciator modules
- Customer interface options
- Generator temperature monitoring
- Modbus monitoring of packages
- E-Stop
- Interconnect harness
- Generator Harness
- Cooling System
- Package mounted radiator
- Remote radiators
- Fuel cooler
- Exhaust System
- Front housing - Standby or mission critical
- Front housing - Prime or continuous
- Exhaust collectors / Manifold
- Exhaust support group
- Mufflers
- Weld flanges
- Aftercooler drain
- Crankcase Systems
- Explosive relief valves
- Crankcase ventilation system
- Generators and Attachments
- Low voltage - 1800 and 3000 Frames - 50 Hz, 3 phase, 1500 rpm, FW, PM, No of leads=6, Pitch 0.6667
- Medium Voltage - 1800 and 3000 Frames - 50 Hz, 3 phase, 1500 rpm, FW, PM, No of leads=6, Pitch 0.6667
- Low Voltage - 1800 and 3000 Frames - 60 Hz, 3 phase, 1800 rpm, FW, PM, No of leads=6, Pitch 0.6667
- Space heater kit
- Thermostat for space heater
- Conversion GP-Top cable entry
- Generator air intake
- Differential current transformers
- Instrumentation
- Pyrometer and thermocouples
- Lube System
- Lube oil heater
- Drain group oil pans
- Lubricating oil
- Electric prelube pumps
- Oil filters
- Mounting
- Rubber anti-vibration mounts
- Spring type linear vibration isolators
- IBC vibration isolators - Shipped loose
- Power Connections
- Center post busbars (LV)
- Side / Rear mounted busbars (LV)
- Harnesses (Breaker)
- Cable entry options (LV)
- Enclosures - Control packaging (LV)
- Power connection covers (LV)
- Neutral ground (LV)
- 1800 Frame generators circuit breaker
- Masterpack breakers
- Paralleling circuit breakers
- 1800 Frame generator side / rear mounted busbars (MV)
- Cable entry options (MV)
- Neutral ground (MV)
- Low voltage connection cable
- Masterpack breaker connections
- Special Tests / Reports
- Generator test report
- PGS test report @ 1.0 power factor
- PGS test report @ 0.8 power factor
- Standard genset TVA (Torsional Vibration Analysis) report
- Custom genset TVA report
- Special test charge - Engine only
- Genset fuel consumption test
- Standard engine test charge
- IBC seismic certification
- OSCOSH1 seismic certification
- Starting / Charging System
- 24 Volt power distribution box
- 24 Volt electric starting motors
- Air starting motor
- Air pressure regulator
- Starter location covers
- 24 Volt battery sets - Dry
- Heavy duty battery sets with rack
- 20 Amp battery chargers
- 35 Amp battery chargers
- 50 Amp battery chargers
- Charging alternators - Dry
- Jacket water heaters
- Jacket water heater wiring groups
- General
- Special paint colors
- Service tools - Engine barring group
- Barring group manual
- Engine barring air powered
- Control GP - Air powered bar group
360° INTERACTIVE
SPECIFICATIONS
- Height Maximum 3307 mm130.2 in
- Length Maximum 7900 mm311 in
- Width Maximum 2756 mm108.5 in
- Minimum Rating 2500 kVA
- Maximum Rating 3100 kVA
- Voltage 220 - 13800 Volts
- Frequency 50 Hz
- Speed 1500 RPM
- Emissions Fuel Strategy Low Fuel Consumption, U.S. EPA Certified for Stationary Emergency Use Only (Tier 2 Nonroad Equivalent Emission Standards)
- Engine Model C175-16 SCAC, V-16, 4-Stroke Water-Cooled Diesel
- Aspiration Turbo Aftercooled
- Governor Type ADEM™ A4
- Fuel System Common Rail
- Bore 175 mm8.89 in
- Displacement 84.67 l5155.88 in³
- Stroke 220 mm8.66 in
- Compression Ratio 50 Hz 16:07:01
- Compression Ratio 60 Hz 15:03:01
- Industry power-generation-diesel-hfo
EQUIPMENT
C175-16 (50 Hz) Standard Equipment
- Air Inlet System
- 4 x Single element canister with service indicator(s)
- Control Panel
- EMCP4 / EMCP4.2
- Emergency stop pushbutton
- 24 Volt DC operation
- Environmental sealed front face.
- Text alarm / event descriptions.
- Generator mounted - rear facing
- Controls
- Speed adjust
- Auto / start / stop control.
- Engine cool-down timer.
- Engine cycle crank
- Alarm acknowledge
- Lamp test
- True RMS AC metering, 3-phase, +/-2% accuracy
- Digital Indicators
- RPM
- DC Volts
- Operating hours
- Oil pressure (psi, kPa or bar)
- Coolant temperature
- Volts (L-L & L-N)
- Frequency (Hz)
- Amps (per phase & average)
- Power Factor (per phase & average)
- Warning / shutdown Indicators
- Low oil pressure
- High coolant temperature
- Overspeed
- Emergency stop
- Failure to start (overcrank)
- Low coolant temperature
- Low coolant level
- Programmable Protective Relaying Functions
- Generator phase sequence
- Over / under voltage
- Over / under frequency
- Reverse power
- Reverse Reactive Power
- Overcurrent
- Communications
- Customer data link (Modbus RTU)
- Accessory module data link
- Serial annunciator module data link
- 6 Programmable digital inputs
- 4 Programmable relay outputs (Form A)
- 2 Programmable relay outputs (Form C)
- 2 Programmable digital outputs
- Cooling System
- SCAC cooling
- Radiator group - shipped loose
- Fan and belt guards
- Coolant drain line and valves
- Coolant Sensors
- Exhaust System
- Dry Exhaust Manifold
- Bolted flange, with bellow for each turbo
- Fuel System
- Primary fuel filter water / fuel water separator
- 10 Micron Spin On Type
- Filters x 3
- Secondary / Tertiary fuel filters
- 4 Micron Spin On Type
- Engine mounted filters X3
- Generator and Attachments
- 3 Phase Brushless
- Salient pole
- 6 Leads
- IEC Platinum stator RTDs
- Voltage Regulator
- Voltage regulator
- Reactive droop capability
- 3 Phase voltage sensing
- RFI suppression
- Min / max exciter limiter
- exciter diode monitor
- Form Wound
- Permanent magnet
- NEMA Class H insulation
- Class H temperature rise at 40C ambient
- (LV) Busbar connections, top/center mounted, top cable entry
- 50 Hz models: IEC standard hole pattern
- (MV) Busbar connections, right side extension box, bottom cable entry
- Anti condensation space heater
- Class F temperature rise at 40C ambient
- Right side extension box, bottom cable entry
- Governing System
- ADEM A4
- Redundant shutdown (Overspeed protection through a duplicate speed sensing system)
- Lube System
- Lubricating oil
- Gear type lube oil pump
- Integral lube oil cooler
- Oil filter, filler and dipstick
- Oil drain lines and valve
- Fumes disposal
- Prelube - required with prime, continuous, and standby
- Mounting Systems
- Rails - Engine / generator
- Rubber anti-vibration mounts (shipped loose)
- Dual 24 volt electric starting motors
- Batteries and battery rack w/cables
- Battery disconnect switch
- General
- Paint - Caterpillar yellow with high gloss black rails & radiator
- Right hand service
- Flywheel and flywheel housing-SAE No. 00
- SAE standard rotation
C175-16 (50 Hz) Optional Equipment
- Air Inlet System
- Single element air cleaner
- Dual element air cleaner
- Air inlet adapters
- Air inlet protection
- Control Panel
- EMCP 4.3, EMCP 4.4
- EMCP 4.4 optional harness
- EMCP and MV&HV power connection locations
- Load share module
- EMCP mounting location - LV / MV
- Customer AC-DC connection mounting location - LV/MV
- Load share module / auxiliary plate and auxiliary box (LV)
- Load share governor
- Frame boxes
- Automatically selected ground
- EMCP voltage and current sensing groups
- Raise lower switch
- Speed adjust
- Annunciator modules
- Customer interface options
- Generator temperature monitoring
- Modbus monitoring of packages
- E-Stop
- Interconnect harness
- Generator Harness
- Cooling System
- Package mounted radiator
- Remote radiators
- Fuel cooler
- Exhaust System
- Front housing - Standby or mission critical
- Front housing - Prime or continuous
- Exhaust collectors / Manifold
- Exhaust support group
- Mufflers
- Weld flanges
- Aftercooler drain
- Crankcase Systems
- Explosive relief valves
- Crankcase ventilation system
- Generators and Attachments
- Low voltage - 1800 and 3000 Frames - 50 Hz, 3 phase, 1500 rpm, FW, PM, No of leads=6, Pitch 0.6667
- Medium Voltage - 1800 and 3000 Frames - 50 Hz, 3 phase, 1500 rpm, FW, PM, No of leads=6, Pitch 0.6667
- Low Voltage - 1800 and 3000 Frames - 60 Hz, 3 phase, 1800 rpm, FW, PM, No of leads=6, Pitch 0.6667
- Space heater kit
- Thermostat for space heater
- Conversion GP-Top cable entry
- Generator air intake
- Differential current transformers
- Instrumentation
- Pyrometer and thermocouples
- Lube System
- Lube oil heater
- Drain group oil pans
- Lubricating oil
- Electric prelube pumps
- Oil filters
- Mounting
- Rubber anti-vibration mounts
- Spring type linear vibration isolators
- IBC vibration isolators - Shipped loose
- Power Connections
- Center post busbars (LV)
- Side / Rear mounted busbars (LV)
- Harnesses (Breaker)
- Cable entry options (LV)
- Enclosures - Control packaging (LV)
- Power connection covers (LV)
- Neutral ground (LV)
- 1800 Frame generators circuit breaker
- Masterpack breakers
- Paralleling circuit breakers
- 1800 Frame generator side / rear mounted busbars (MV)
- Cable entry options (MV)
- Neutral ground (MV)
- Low voltage connection cable
- Masterpack breaker connections
- Special Tests / Reports
- Generator test report
- PGS test report @ 1.0 power factor
- PGS test report @ 0.8 power factor
- Standard genset TVA (Torsional Vibration Analysis) report
- Custom genset TVA report
- Special test charge - Engine only
- Genset fuel consumption test
- Standard engine test charge
- IBC seismic certification
- OSCOSH1 seismic certification
- Starting / Charging System
- 24 Volt power distribution box
- 24 Volt electric starting motors
- Air starting motor
- Air pressure regulator
- Starter location covers
- 24 Volt battery sets - Dry
- Heavy duty battery sets with rack
- 20 Amp battery chargers
- 35 Amp battery chargers
- 50 Amp battery chargers
- Charging alternators - Dry
- Jacket water heaters
- Jacket water heater wiring groups
- General
- Special paint colors
- Service tools - Engine barring group
- Barring group manual
- Engine barring air powered
- Control GP - Air powered bar group
RELATED PRODUCTS
-ab8d163df39b274212ec55d9c8475014.jpeg)
3412C (50 Hz)
power generation diesel hfo
- Height Maximum: 1906 mm75 in
- Length Maximum: 162.4 mm4135 in
- Width Maximum: 1989 mm78.3 in
3512A (50 Hz)
power generation diesel hfo
- Minimum Rating: 1000 kVA
- Maximum Rating: 1400 kVA
- Voltage: 220 to 13800 Volts
3512B (50 Hz)
power generation diesel hfo
- Height Maximum: 2367 mm93.2 in
- Length Maximum: 5637 mm221.9 in
- Width Maximum: 2286 mm90 in
3516 (50 Hz)
power generation diesel hfo
- Height Maximum: 2367 mm93.2 in
- Length Maximum: 5919 mm232.9 in
- Width Maximum: 2286 mm90 in
3516B (50 Hz)
power generation diesel hfo
- Height Maximum: 2367 mm93.2 in
- Length Maximum: 5928 mm233.4 in
- Width Maximum: 2286 mm90 in
3516B DGB™ (50 Hz)
power generation diesel hfo
- Minimum Rating: 1750 kVA
- Maximum Rating: 2275 kVA
- Voltage: 220 to 11000
3516E (50 Hz)
power generation diesel hfo
- Height Maximum: 3476 mm136.9 in
- Length Maximum: 9195 mm362 in
- Width Maximum: 2552 mm100.5 in
C1.5 (50 Hz)
power generation diesel hfo
- Height Maximum: 1054 mm41.5 in
- Length Maximum: 1400 mm55.1 in
- Width Maximum: 620 mm24.4 in
C2.2 (50 Hz)
power generation diesel hfo
- Height Maximum: 1115 mm43.9 in
- Length Maximum: 1500 mm59.1 in
- Width Maximum: 620 mm24.4 in
