G16CM34 Gas Engine oil and ga

  • Minimum Rating 6100 ekW8180 HP
  • Maximum Rating 6100 ekW8180 HP
  • Compression Ratio 11.4:1

SPECIFICATIONS

  • Minimum Rating 6100 ekW8180 HP
  • Maximum Rating 6100 ekW8180 HP
  • Compression Ratio 11.4:1
  • Aspiration Turbocharged-2 Stage Aftercooled
  • Bore 13.38 in340 mm
  • Displacement 610 L (37,209 in3)
  • Stroke 16.54 in420 mm
  • Emissions U.S. EPA SI NSPS Site Compliant Capable
  • Oil Change Interval 7500 hrs
  • Rotation From Flywheel End Counterclockwise
  • Flywheel Teeth 408
  • Weight Dry 181000 lb82000 kg
  • Governor And Protection Electronic (ADEM™ A3)
  • Industry oil-and-gas

EQUIPMENT

G16CM34 Gas Engine Standard Equipment

  • Air Inlet System
    • Turbocharger Inlet Adapter - provides a flexible connection between engine mounted turbocharger inlet and customer inlet air piping
    • Air Filter Units - Two air filter housings for remote installation, one per turbocharger, are designed for normal environmental conditions. Each filter housing contains six (6) dry filter elements. A single filter housing with twelve (12) filter elements is offered as optional
    • Air Intake Silencer – an in-line tubular air silencers designed for 30 dB(A) noise reduction
  • Cooling System
    • The engine includes an auxiliary skid that combines the cooling system and lubrication system functions. The standard cooling system separates the High Temperature (HT – includes JW) circuit from the Low Temperature (LT – includes 2nd stage of aftercooler) circuit. Thermostatic valves are included for each circuit. Two-stage charge air cooler splits heat load between the HT and LT circuit, reducing the heat load to the LT system, minimizing cooler costs. The lube oil system includes a automatic filter, plate and frame oil cooler, an engine-mounted gear-driven lubrication pump, and an electric motor-driven pre/post-lubricating pump. A pneumatically actuated thermostatic valve (controlled by the engine control panel) controls the lube oil temperature. All components mounted on a single baseplate with drip pan for pollution control. Interconnecting pipe between engine and cooling water/lube oil skid are by customer. Engine controls are by customer.
    • Set of Flexible Connectors at the engine for cooling water piping
  • Crankcase Ventilation Systems
    • Design includes multi-stage oil remover with metal elements and paper filter
    • Capacity – 340 m3/h (200 scfm)
  • Cylinder Block
    • One-piece design for strength and rigidity
    • Underslung crankshaft reduces weight and provides easy access to bearings for service
    • Dry cylinder block (waterless) offers reduced repair times and increased strength
    • Crankcase pressure relief devices
    • Designed for block or skid mounting
  • Cylinder Head
    • Individual cylinder heads with two inlet and two exhaust valves per cylinder
    • Water-cooled exhaust seats to increase life
    • Nitrided valves with automatic rotators
  • Drive Coupling
    • A torsionally elastic high damping steel spring coupling is provided. The TVA study with up to eight compressor load cases is included.
  • Engine Controls and Instrumentation
    • The engine utilizes the ADEM A3 engine management system for speed regulation, individual cylinder detonation control, closed loop air/fuel ratio control, engine monitoring and protection. Electronically controlled pneumatic actuated valves control the main and pilot fuel gas pressure. System also includes an operator interface for displaying operating parameters and system messages. This system includes a local control panel with PLC for additional engine management and protection. Protection provided by this system includes: - Engine control panel with PLC and operator control interface - Floor-standing enclosure with window kit for touch screen - Supplied local control panel includes space to incorporate compressor PLC, which can be displayed on same screen
  • Exhaust Gas System
    • - Two front-mounted (non-flywheel end) turbochargers designed for constant pressure supercharging - Variable geometry turbochargers will provide optimal air-fuel ratio control through a wide operating range by controlling its own manifold pressure - Exhaust gas pipe manifold with one expansion joint per cylinder; connection allows easy maintenance and quick cylinder head removal
  • Flywheels & Flywheel Housings
    • A flywheel with starting ring gear is shipped mounted, cover/guard not included.
  • Fuel System
    • Gas Regulating Unit – independently controls the gas supply pressure to the main combustion chamber and pre-chamber. The skid is certified for Class 1, Division 2, Group D hazardous location.
    • Set of Flexible Connectors at the engine for main chamber and pre-chamber piping
  • Lube-Oil System
    • The lube-oil part of the auxiliary skid includes the following components:
  • Painting
    • The engine is painted Cat yellow, other colors can be provided. Caterpillar Motoren's standard paint system will be used.
  • Starting System
    • Equipped with turbine-type air starters (TDI) uses compressed air or natural gas for engine starting; 1,034 kPa (150 psi) minimum air pressure. Rear mounted.
    • Set of Flexible Connectors at the engine for start air/gas piping
    • Barring Device Controller – handheld controller with hoses and oiler
  • Testing
    • Each engine is factory tested before shipment from Kiel, Germany. Test reports will be provided as part of the standard documentation.
  • General
    • Flexible Coupling – flexible coupling between engine and driven equipment (compressor)
    • Barring Device Controller – handheld controller with hoses and oiler
    • Torsional Vibration Analysis (TVA) of up to eight (8) load cases

G16CM34 Gas Engine Optional Equipment

  • Air Inlet System
    • Inlet air Pre-heater – required for inlet air temperature below -20°C (-4°F)
  • Exhaust Gas System
    • Exhaust Ventilation System – purge the entire exhaust gas system to maintain gas concentration below ignition point reducing the risk of exhaust gas explosion. The skid is certified for Class 1, Division 2, Group D hazardous location
  • General
    • Bearing Temperature Monitor – to monitor temperature of the main crankshaft bearings and the connecting rod big end bearings. •    Engine Special Tools – set of special tools for GCM34 engines.

RELATED PRODUCTS

CN1566 Electric Motor - Oil-and-gas

CN1566 Electric Motor

oil and gas

  • Electric Motor Type: Squirrel Cage Induction Motor
  • Full Load Speed: 1189 r/min1189 r/min
  • Mounting Designation: F1 or F2
Get a quote
CN3086 Electric Motor for Gas Compression - Oil-and-gas

CN3086 Electric Motor for Gas Compression

oil and gas

  • Electric Motor Type: Squirrel Cage Induction Motor
  • Full Load Speed: 892 r/min892 r/min
  • Mounting Designation: F1 or F2
Get a quote
CN3586 Electric Motor for Gas Compression - Oil-and-gas

CN3586 Electric Motor for Gas Compression

oil and gas

  • Electric Motor Type: Squirrel Cage Induction Motor
  • Full Load Speed: 894 rpm
  • Mounting Designation: F1 or F2
Get a quote
CN5086 Electric Motor - Oil-and-gas

CN5086 Electric Motor

oil and gas

  • Electric Motor Type: Squirrel Cage Induction Motor
  • Full Load Speed: 894 r/min894 r/min
  • Mounting Designation: F1 or F2
Get a quote
3406C - Oil-and-gas

3406C

oil and gas

  • Minimum Rating: 217 bkW292 BHP
  • Maximum Rating: 359 bkW482 BHP
  • Aspiration: Turbocharged Aftercooled
Get a quote
3412 - Oil-and-gas

3412

oil and gas

  • Minimum Rating: 476 bkW638 BHP
  • Maximum Rating: 551 bkW739 BHP
  • Aspiration: Turbocharged Aftercooled
Get a quote
3508 - Oil-and-gas

3508

oil and gas

  • Minimum Rating: 709 bkW950 BHP
  • Maximum Rating: 795 bkW1065 BHP
  • Aspiration: Turbocharged Aftercooled
Get a quote
3512 - Oil-and-gas

3512

oil and gas

  • Minimum Rating: 1066 bkW1430 BHP
  • Maximum Rating: 1195 bkW1600 BHP
  • Aspiration: Turbocharged Aftercooled
Get a quote
3516 - Oil-and-gas

3516

oil and gas

  • Minimum Rating: 1417 bkW1900 BHP
  • Maximum Rating: 1480 bkW1985 BHP
  • Aspiration: Turbocharged Aftercooled
Get a quote