C7 ACERT™ (Hazardous Location) oil and ga

  • Minimum Rating 153 bkW205 BHP
  • Maximum Rating 205 bkW275 BHP
  • Aspiration Turbocharged-Aftercooled

SPECIFICATIONS

  • Minimum Rating 153 bkW205 BHP
  • Maximum Rating 205 bkW275 BHP
  • Aspiration Turbocharged-Aftercooled
  • Bore 110 mm4.3 in
  • Displacement 7.2 l442 in³
  • Stroke 127 mm5 in
  • Length 1113 mm4.38 in
  • Width 851 mm33.5 in
  • Height 1113 mm43.8 in
  • Emissions EPA & CARB Non-Road Tier 3, EU Stage IIIA, EPA Marine Tier 2, IMO Tier II
  • Rotation From Flywheel End Counterclockwise
  • Flywheel And Flywheel Housing SAE 1,2, or 3
  • Flywheel Teeth 156 (SAE 1), 134 (SAE 2), 126 (SAE 3)
  • Lube Oil System Refill 34 l36 gal (US)
  • Cooling System 74 l78.2 gal (US)
  • Governor And Protection Electronic ADEM™ A4
  • Weight 712 kg1570 lb
  • Industry oil-and-gas

EQUIPMENT

C7 ACERT™ (Hazardous Location) Standard Equipment

  • Air Inlet System
    • Turbocharger, separate circuit (SCAC) or remote (REMAC) aftercooler
    • Single, right-side, center-mounted turbo with water-cooled turbine housing
    • Air inlet, RH side, rear facing, 101.6 mm (4 in.) connection type
  • Control System
    • Electronic governing, PTO speed control
    • Programmable ratings
    • Cold mode start strategy
    • Automatic altitude compensation
    • Fuel cooled ECU
    • Power compensation for fuel temperature
    • Programmable low and high idle
    • Electronic diagnostics and fault logging
    • Programmable monitoring system (engine speed, temperature, pressure)
    • J1939 broadcast (diagnostic and engine status)
    • Certified electrical control system
    • Derated engine: automatic ambient temperature compensation
  • Cooling System
    • Thermostats and housing, front-facing outlet — 51 mm (2.01 in) connection
    • Jacket water pump — belt-driven, centrifugal
    • Water pump — inlet RH front vertical inlet (pointing down) — 63 mm (2.48 in)
  • Exhaust System
    • Single, right-side, center-mounted turbo with water-cooled turbine housing
    • Exhaust manifold — water-cooled
    • Front turbo exhaust
  • Flywheels and Flywheel Housing
    • Mandatory selection of: SAE No. 1, SAE No. 2, or SAE No. 3 flywheel and housing SAE standard rotation
  • Fuel System
    • HEUI fuel system
    • Fuel filter — secondary, LH front (2-micron high performance)
    • Fuel transfer pump — left front
    • Fuel priming pump — left front
  • Lube System
    • Crankcase breather — top rear
    • Crankcase fumes disposal — RH
    • Oil cooler — RH
    • Oil filter — RH
    • Oil pan — front sump, 31 L (33 qt) oil change capacity
    • Oil filler — front top valve cover
    • Oil level gauge — LH rear
    • Engine oil pump — gear-driven
    • Oil valve sampling, RH
  • Power Take-Offs
    • Crankshaft drive pulley — 2 grooves, 190 mm (7.5 in) diameter, 22.3 mm (0.88 in) wide
  • General
    • Vibration damper
    • Lifting eyes
    • Literature
    • No paint
  • Mandatory Options
    • Flywheel housing and flywheel
    • Primary filter/water separator
    • Turbo orientation

C7 ACERT™ (Hazardous Location) Optional Equipment

  • Air Compressors
    • Air compressor governor
  • Air Inlet System
    • Precleaner
    • Air inlet elbow
    • Charging System
    • Cooling System
  • Emissions Certifications
    • IMO certification
  • Flywheels and Flywheel Housing
    • Crankshaft seal
  • Instrumentation
    • Gauges and instrument panels
  • Lube System
    • Oil pans
    • Drain and cover
    • Remote oil filters
    • Lubricating oils
  • Mounting System
    • Structural steel base
    • Engine support — front and rear
  • Power Take-Offs
    • Rear enclosed clutches
    • Hydraulic pump drives
    • Crankshaft pulleys
  • General
    • Tool set

RELATED PRODUCTS

CN1566 Electric Motor - Oil-and-gas

CN1566 Electric Motor

oil and gas

  • Electric Motor Type: Squirrel Cage Induction Motor
  • Full Load Speed: 1189 r/min1189 r/min
  • Mounting Designation: F1 or F2
Get a quote
CN3086 Electric Motor for Gas Compression - Oil-and-gas

CN3086 Electric Motor for Gas Compression

oil and gas

  • Electric Motor Type: Squirrel Cage Induction Motor
  • Full Load Speed: 892 r/min892 r/min
  • Mounting Designation: F1 or F2
Get a quote
CN3586 Electric Motor for Gas Compression - Oil-and-gas

CN3586 Electric Motor for Gas Compression

oil and gas

  • Electric Motor Type: Squirrel Cage Induction Motor
  • Full Load Speed: 894 rpm
  • Mounting Designation: F1 or F2
Get a quote
CN5086 Electric Motor - Oil-and-gas

CN5086 Electric Motor

oil and gas

  • Electric Motor Type: Squirrel Cage Induction Motor
  • Full Load Speed: 894 r/min894 r/min
  • Mounting Designation: F1 or F2
Get a quote
3406C - Oil-and-gas

3406C

oil and gas

  • Minimum Rating: 217 bkW292 BHP
  • Maximum Rating: 359 bkW482 BHP
  • Aspiration: Turbocharged Aftercooled
Get a quote
3412 - Oil-and-gas

3412

oil and gas

  • Minimum Rating: 476 bkW638 BHP
  • Maximum Rating: 551 bkW739 BHP
  • Aspiration: Turbocharged Aftercooled
Get a quote
3508 - Oil-and-gas

3508

oil and gas

  • Minimum Rating: 709 bkW950 BHP
  • Maximum Rating: 795 bkW1065 BHP
  • Aspiration: Turbocharged Aftercooled
Get a quote
3512 - Oil-and-gas

3512

oil and gas

  • Minimum Rating: 1066 bkW1430 BHP
  • Maximum Rating: 1195 bkW1600 BHP
  • Aspiration: Turbocharged Aftercooled
Get a quote
3516 - Oil-and-gas

3516

oil and gas

  • Minimum Rating: 1417 bkW1900 BHP
  • Maximum Rating: 1480 bkW1985 BHP
  • Aspiration: Turbocharged Aftercooled
Get a quote
Get a quote