C32 IMO II marine power system

  • Minimum Rating 590 bkW791 BHP
  • Maximum Rating 994 bkW1333 BHP
  • Aspiration TTA

SPECIFICATIONS

  • Minimum Rating 590 bkW791 BHP
  • Maximum Rating 994 bkW1333 BHP
  • Aspiration TTA
  • Bore 145 mm5.7 in
  • Displacement 32.1 l1959 in³
  • Stroke 162 mm6.4 in
  • Configuration Vee 12, 4-Stroke-Cycle Diesel
  • Width 1528 mm60.2 in
  • Rotation From Flywheel End Counterclockwise
  • Maximum Height 1587 mm62.5 in
  • Maximum Length 2284 mm89.9 in
  • Minimum Dry Weight 3152 kg6950 lb
  • Minimum Height 1547 mm60.9 in
  • Minimum Length 2121 mm83.5 in
  • Maximum Dry Weight 3248 kg7160 lb
  • Industry marine-power-systems

EQUIPMENT

C32 IMO II Standard Equipment

  • AIR INLET SYSTEM
    • Separate circuit after-cooled (SCAC)
    • Air cleaner
    • Turbocharger, jacket water cooled
    • Turbocharger inlet, 152 mm (6 in) OD straight connection
  • CONTROL SYSTEM
    • Programmable Low Idle (550 - 750 rpm)
    • Programmable High Idle Limit for WOSR Ratings
    • Electronic diagnostics and fault logging
    • Engine and transmission monitoring (speed, temperature, pressure)
    • Electronic fuel/air ratio control
    • Engine Protection Mode for extended ambient conditions
    • 70-pin customer connector
    • Throttle Input signal options
    • 0 - 5 Volts
    • 4 - 20 mA
    • PWM (Pulse Width Modulated)
  • COOLING SYSTEM
    • Separate Circuit After-Cooling (SCAC) for both HEX and Keel cooled engines
    • Jacket Water (JW) and SCAC Heat Exchangers Shell & Tube for HEX cooled engines
    • SCAC pump, gear driven
    • Jacket water pump, gear driven
    • Sea water pump, bronze impeller, gear driven, when selected for Hex cooled engines
    • Sea water Pump & JW Heat Exchanger Connection: 76.2 mm (3in) ID Standard 4 Bolt ANSI Flange Connection
    • Keel Connections: 76.2 mm (3in) ID Standard 4 Bolt
    • SCAC and JW shunt tanks for maintaining proper pump inlet pressures
  • EXHAUST SYSTEM
    • Water-cooled exhaust manifold & turbocharger
    • 4 Bolt 130 mm (5.12 in) diameter flanged outlet
  • FLYWHEELS & FLYWHEEL HOUSINGS
    • SAE standard rotation (CCW facing exciter end)
    • Flywheel Housing: SAE No. 0, Flywheel: 18 inch, 136 teeth
  • FUEL SYSTEM
    • Duplex Fuel Filters, Spin-on, RH & LH service
    • Fuel connections size: r driven
    • Plate-type fuel cooler installed behind Aftercooler Shunt Tank
    • Fuel transfer pump, gear driven
    • Manual fuel priming pump
    • Hybrid fuel line design
  • LUBE SYSTEM
    • Simplex Oil Filters, RH or LH service
    • Deep sump oil pan
    • RH or LH service oil filler locations
    • RH or LH service dipstick
    • Oil pump, gear driven
  • MOUNTING SYSTEM
    • Front support - 33 inches wide
  • POWER TAKE-OFFS
    • Front Poly-V groove pulley (Quantity 1) for auxiliary drives
  • GENERAL
    • Common electrical bonding point
    • Engine does not ship with zinc components

C32 IMO II Optional Equipment

  • EXHAUST SYSTEM
    • Dry Elbows
    • Flexible Fitting
    • Flange
    • Muffler
    • Muffler Spark Arresting
  • AIR INLET SYSTEM
    • Air Inlet Adapter
  • CHARGING SYSTEM
    • Battery Chargers
    • Charging Alternators
    • Ammeter
  • CONTROL SYSTEM
    • Load Sharing Attachment
    • Instrument Panels
    • Caterpillar Alarm Protection
    • Fuel and Oil Shielding
  • FUEL SYSTEM
    • Water Separator
  • GENERAL
    • Fumes Disposal System
  • INSTRUMENTATION
    • Instrument Panels
    • OEM Wiring Harness
    • Engine to Engine Harness
    • Gauges
    • Transmission Sensors
    • Exhaust Temperature Sensors
  • LUBE SYSTEM
    • Duplex Oil Filters
    • Sump Pump
  • POWER TAKE-OFFS
    • Rear Hydraulic Pump Drive
  • STARTING SYSTEM
    • Electric Starting Motors - Single 24 Volt
    • Air Starting Motor
    • Dual Starting Motors (Electric and Air)
    • Air Start Accessories
    • Starting Aids - JW Heaters
    • Battery Sets - 24 Volt - Dry
  • MOUNTING SYSTEM
    • Front Support
    • Rear Support
    • Isolators Mounts
    • Adapter Kits
  • PACKING
    • Engine Protective Cover
    • Storage Preservation
    • Export Packing

RELATED PRODUCTS

3512E - Marine-power-systems

3512E

marine power systems

  • Aspiration: TA
  • Bore: 170 mm6.69 in
  • Displacement: 58.6 l3574 in³
Get a quote
3516E - Marine-power-systems

3516E

marine power systems

  • Aspiration: TA
  • Bore: 170 mm6.69 in
  • Displacement: 78 l4765 in³
Get a quote
C18 IMO II - Marine-power-systems

C18 IMO II

marine power systems

  • Minimum Rating: 301 bkW404 BHP
  • Maximum Rating: 492 bkW660 BHP
  • Aspiration: TA, TTA
Get a quote
C18 Tier 3 - Marine-power-systems

C18 Tier 3

marine power systems

  • Minimum Rating: 465 bkW624 BHP
  • Maximum Rating: 599 bkW803 BHP
  • Aspiration: TA, TTA
Get a quote
C280 - Marine-power-systems

C280

marine power systems

  • Minimum Rating: 1730 bkW2320 BHP
  • Maximum Rating: 5420 bkW7268 BHP
  • Aspiration: TA
Get a quote
C32 IMO II - Marine-power-systems

C32 IMO II

marine power systems

  • Minimum Rating: 590 bkW791 BHP
  • Maximum Rating: 994 bkW1333 BHP
  • Aspiration: TTA
Get a quote
C32 IMO III - Marine-power-systems

C32 IMO III

marine power systems

  • Minimum Rating: 262 bkW352 BHP
  • Maximum Rating: 874 bkW1172 BHP
  • Aspiration: Turbocharged-aftercooled aspiration
Get a quote
C32 Tier 3 - Marine-power-systems

C32 Tier 3

marine power systems

  • Minimum Rating: 781 bkW1047 BHP
  • Maximum Rating: 994 bkW1333 BHP
  • Aspiration: TTA
Get a quote
C32 Tier 3 / IMO II - Marine-power-systems

C32 Tier 3 / IMO II

marine power systems

  • Minimum Rating: 234 bkW314 BHP
  • Maximum Rating: 994 bkW1333 BHP
  • Aspiration: Turbocharged-aftercooled aspiration
Get a quote
Get a quote