C32 ACERT IMO II marine power system

  • Aspiration TTA
  • Bore 145 mm5.71 in
  • Displacement 32.1 l1959 in³

SPECIFICATIONS

  • Aspiration TTA
  • Bore 145 mm5.71 in
  • Displacement 32.1 l1959 in³
  • Stroke 162 mm6.38 in
  • Configuration Vee 12, 4-Stroke-Cycle Diesel
  • Emissions IMO II, EU IW
  • Rotation From Flywheel End Counterclockwise
  • Power Range 660-1450 bhp (492-1081 bkW)
  • Maximum Height 1587 mm62.5 in
  • Maximum Length 2284 mm83.5 in
  • Maximum Width 1528 mm60.17 in
  • Minimum Dry Weight 3152 kg6950 lb
  • Minimum Height 1547 mm60.9 in
  • Minimum Length 2121 mm77.8 in
  • Minimum Width 1528 mm60.17 in
  • Speed Range 1600-2300 rpm
  • Industry marine-power-systems

EQUIPMENT

C32 ACERT IMO II Standard Equipment

  • AIR INLET SYSTEM
    • Separate Circuit After-Cooled (SCAC
    • Air cleaner
    • Turbochargers, jacket water cooled
    • Turbochargers inlet, 152 mm (6 in) OD straight connection
  • CONTROL SYSTEM
    • Programmable Low Idle (550 - 750 rpm)
    • WOSR (Wide Operating Speed Range) available for - A, B, & C Ratings
    • Programmable High Idle Limit for WOSR Ratings
    • Electronic diagnostics and fault logging
    • Engine and transmission monitoring (speed, temperature, pressure)
    • Electronic fuel/air ratio control
    • Engine Protection Mode for extended ambient conditions
    • Torque Limiting functionality for WOSR ratings only
    • 70-pin customer connector
    • Throttle Input signal options
  • COOLING SYSTEM
    • Separate Circuit After-Cooling (SCAC) for Heat Exchanged (HEX) & Keel cooled engines
    • Jacket Water (JW) and SCAC Heat Exchangers Shell & Tube for HEX cooled engines
    • SCAC pump, gear driven
    • Jacket water pump, gear driven
    • Sea water pump, bronze impeller, gear driven, for HEX cooled engines only
    • Sea water Pump & JW Heat Exchanger Connection: 76.2 mm (3in) ID Standard
    • Keel Connections: 76.2 mm (3in) ID Standard 4 Bolt ANSI Flange Connection
    • SCAC and JW shunt tanks for maintaining proper pump inlet pressures
  • EXHAUST SYSTEM
    • 4 Bolt 130 mm (5.12 in) diameter flanged outlet
    • Water-cooled exhaust manifold & turbocharger
  • FLYWHEELS & FLYWHEEL HOUSINGS
    • SAE standard rotation (CCW facing exciter end)
    • Flywheel Housing: SAE No. 0, Flywheel: 18 inch, 136 teeth
  • FUEL SYSTEM
    • Duplex Fuel Filters, Spin-on, RH & LH service
    • Fuel connections size:Supply JIC 37 Deg -10 (7/8-14), Return JIC 37 Deg -8 (3/4-16)
    • Plate Type Fuel Cooler installed behind Aftercooler Shunt Tank
    • Fuel transfer pump, gear driven
    • Manual fuel priming pump
    • Hybrid fuel line design
  • LUBE SYSTEM
    • Simplex Oil Filters, RH or LH service
    • Deep sump oil pan
    • RH or LH service oil filler locations
    • RH or LH service dipstick
    • Oil pump, gear driven
  • MOUNTING SYSTEM
    • Front support - adjustable
  • POWER TAKE-OFFS
    • Front Poly-V groove pulley (Quantity 1) for auxiliary drives
  • GENERAL
    • Common electrical bonding point
    • Engine does not ship with zinc components

C32 ACERT IMO II Optional Equipment

  • Air Inlet Systems
    • Air Inlet Cleaner
    • Air Inlet Adapter
  • Charging Systems
    • Battery Charger
    • Charging Alternators
    • Ammeter
  • Cooling System
    • Marine Gear/Transmission Oil Coolers
    • Connections
  • Exhaust System
    • Dual Elbow
    • Flexible Fitting
    • Dual Muffler
    • Muffler Spark Arresting
    • Flange
  • Fuel System
    • Water Separator
  • Instrumentation
    • OEM Wiring Harness
    • Engine to Engine Harness
    • Instrument Panels
    • Exhaust Temperature Sensors
    • Wiring Harness
    • Gauges
    • Transmission Sensors
  • Lube System
    • Transmission Oil Cooler
    • Manual Sump Pump
    • Duplex Oil Filters
  • Protection System
    • Fuel and Oil Shielding
  • Starting System
    • Air Starting Motor
    • Air Start Accessories
    • Electric Starting Motors - Single 24 Volt
    • Starting Aids
    • Battery Sets - 24 Volt - Dry
    • Dual Starting Motors (Electric and Air)
  • Packing
    • Engine Protective Cover
    • Export Packing
    • Storage Preservation
  • Mounting System
    • Front Support
    • Adapter Kits
    • Isolator Mounts
  • Power Take-Offs
    • Front Enclosed Clutches
    • Rear Hydraulic Pump Drive
  • GENERAL
    • Fumes Disposal
  • CONTROL SYSTEM
    • Instrument Panels
    • CATERPILLAR ALARM AND PROTECTION
    • Fuel and Oil Shielding

RELATED PRODUCTS

3512E - Marine-power-systems

3512E

marine power systems

  • Aspiration: TA
  • Bore: 170 mm6.69 in
  • Displacement: 58.6 l3574 in³
Get a quote
3516E - Marine-power-systems

3516E

marine power systems

  • Aspiration: TA
  • Bore: 170 mm6.69 in
  • Displacement: 78 l4765 in³
Get a quote
C18 IMO II - Marine-power-systems

C18 IMO II

marine power systems

  • Minimum Rating: 301 bkW404 BHP
  • Maximum Rating: 492 bkW660 BHP
  • Aspiration: TA, TTA
Get a quote
C18 Tier 3 - Marine-power-systems

C18 Tier 3

marine power systems

  • Minimum Rating: 465 bkW624 BHP
  • Maximum Rating: 599 bkW803 BHP
  • Aspiration: TA, TTA
Get a quote
C280 - Marine-power-systems

C280

marine power systems

  • Minimum Rating: 1730 bkW2320 BHP
  • Maximum Rating: 5420 bkW7268 BHP
  • Aspiration: TA
Get a quote
C32 IMO II - Marine-power-systems

C32 IMO II

marine power systems

  • Minimum Rating: 590 bkW791 BHP
  • Maximum Rating: 994 bkW1333 BHP
  • Aspiration: TTA
Get a quote
C32 IMO III - Marine-power-systems

C32 IMO III

marine power systems

  • Minimum Rating: 262 bkW352 BHP
  • Maximum Rating: 874 bkW1172 BHP
  • Aspiration: Turbocharged-aftercooled aspiration
Get a quote
C32 Tier 3 - Marine-power-systems

C32 Tier 3

marine power systems

  • Minimum Rating: 781 bkW1047 BHP
  • Maximum Rating: 994 bkW1333 BHP
  • Aspiration: TTA
Get a quote
C32 Tier 3 / IMO II - Marine-power-systems

C32 Tier 3 / IMO II

marine power systems

  • Minimum Rating: 234 bkW314 BHP
  • Maximum Rating: 994 bkW1333 BHP
  • Aspiration: Turbocharged-aftercooled aspiration
Get a quote
Get a quote