NEW / / oil and gas / C18 ACERT™
C18 ACERT™
SPECIFICATIONS
EQUIPMENT
RELATED PRODUCTS
- Minimum Rating 447 bkW600 BHP
- Maximum Rating 597 bkW800 BHP
- Aspiration Turbocharged-Aftercooled
SPECIFICATIONS
- Minimum Rating 447 bkW600 BHP
- Maximum Rating 597 bkW800 BHP
- Aspiration Turbocharged-Aftercooled
- Bore 145 mm5.7 in
- Displacement 18 l1106 in³
- Stroke 183 mm7.2 in
- Length 1889 mm74.4 in
- Width 1091 mm43 in
- Height 1380 mm54.3 in
- Emissions U.S. EPA Tier, Tier 2 or non-certified
- Engine Weight Net Dry 1769 kg3900 lb
- Oil Change Interval 500 h500 h
- Rotation From Flywheel End Counterclockwise
- Flywheel And Flywheel Housing SAE No. 1
- Flywheel Teeth 113
- Lube Oil System Refill 37.7 l10 gal (US)
- Cooling System Engine 50 l13.3 gal (US)
- Rated Speed 1750 r/min1750 r/min
- Industry oil-and-gas
EQUIPMENT
C18 ACERT™ Standard Equipment
- Air Inlet System
- Dual turbocharger: front and rear inlet 127.mm (5.0 in)
- Separate Circuit Aftercooled (SCAC)
- Charging System
- Charging alternator 24 volt, 50 amp
- Control System
- Dual Electronic Control Units (ECU), primary and secondary
- Electronic governing, PTO speed control
- Programmable ratings
- Cold start capability to -20° C (-4° F)
- Automatic altitude compensation
- Power compensation for fuel temperature
- Programmable low and high idle and total engine limit
- Electronic diagnostics and fault logging
- Engine monitoring system SAE J1939 broadcast and control
- Cooling System
- Thermostats and housing, vertical outlet
- Jacket water pump, centrifugal
- Heat exchanger installed
- Expansion tank
- Exhaust System
- Exhaust manifold, dry
- Dual turbo: exhaust elbow, dry 203 mm (8 in)
- Flywheels and Flywheel Housing
- SAE No. 1 flywheel
- SAE No. 1 flywheel housing
- Power take-off (PTO) flywheel stub shaft
- Fuel System
- Electronic unit injector
- Fuel filter, secondary (2 micron high performance)
- Fuel transfer pump
- Fuel priming pump
- Fuel sample valve, mounted on fuel filter base
- Primary fuel filter
- Water separator
- Instrumentation
- Instrument panel, LH
- Engine oil pressure gauge
- Voltmeter gauge
- Water temperature gauge
- Tachometer/engine hour meter
- Lube System
- Open crankcase ventilation system
- Oil cooler
- Lube oil filter
- Front sump oil pan
- Oil filler
- Oil dipstick
- Oil pump
- Protection System
- Stop-Start System, automatic (compatible with NFPA 20 requirements, able to be energized from either of two battery sources and capable of manual starter actuation)
- Starting System
- 24 volt, LH electric starting motor
- Jacket water heater (3 kW, 120-240 volt)
- General
- Vibration damper
- Lifting eyes
- Automatic variable timing, electronic
- Electronic installation kit, 70 pin connector (connectors, pins, sockets)
360° INTERACTIVE
SPECIFICATIONS
- Minimum Rating 447 bkW600 BHP
- Maximum Rating 597 bkW800 BHP
- Aspiration Turbocharged-Aftercooled
- Bore 145 mm5.7 in
- Displacement 18 l1106 in³
- Stroke 183 mm7.2 in
- Length 1889 mm74.4 in
- Width 1091 mm43 in
- Height 1380 mm54.3 in
- Emissions U.S. EPA Tier, Tier 2 or non-certified
- Engine Weight Net Dry 1769 kg3900 lb
- Oil Change Interval 500 h500 h
- Rotation From Flywheel End Counterclockwise
- Flywheel And Flywheel Housing SAE No. 1
- Flywheel Teeth 113
- Lube Oil System Refill 37.7 l10 gal (US)
- Cooling System Engine 50 l13.3 gal (US)
- Rated Speed 1750 r/min1750 r/min
- Industry oil-and-gas
EQUIPMENT
C18 ACERT™ Standard Equipment
- Air Inlet System
- Dual turbocharger: front and rear inlet 127.mm (5.0 in)
- Separate Circuit Aftercooled (SCAC)
- Charging System
- Charging alternator 24 volt, 50 amp
- Control System
- Dual Electronic Control Units (ECU), primary and secondary
- Electronic governing, PTO speed control
- Programmable ratings
- Cold start capability to -20° C (-4° F)
- Automatic altitude compensation
- Power compensation for fuel temperature
- Programmable low and high idle and total engine limit
- Electronic diagnostics and fault logging
- Engine monitoring system SAE J1939 broadcast and control
- Cooling System
- Thermostats and housing, vertical outlet
- Jacket water pump, centrifugal
- Heat exchanger installed
- Expansion tank
- Exhaust System
- Exhaust manifold, dry
- Dual turbo: exhaust elbow, dry 203 mm (8 in)
- Flywheels and Flywheel Housing
- SAE No. 1 flywheel
- SAE No. 1 flywheel housing
- Power take-off (PTO) flywheel stub shaft
- Fuel System
- Electronic unit injector
- Fuel filter, secondary (2 micron high performance)
- Fuel transfer pump
- Fuel priming pump
- Fuel sample valve, mounted on fuel filter base
- Primary fuel filter
- Water separator
- Instrumentation
- Instrument panel, LH
- Engine oil pressure gauge
- Voltmeter gauge
- Water temperature gauge
- Tachometer/engine hour meter
- Lube System
- Open crankcase ventilation system
- Oil cooler
- Lube oil filter
- Front sump oil pan
- Oil filler
- Oil dipstick
- Oil pump
- Protection System
- Stop-Start System, automatic (compatible with NFPA 20 requirements, able to be energized from either of two battery sources and capable of manual starter actuation)
- Starting System
- 24 volt, LH electric starting motor
- Jacket water heater (3 kW, 120-240 volt)
- General
- Vibration damper
- Lifting eyes
- Automatic variable timing, electronic
- Electronic installation kit, 70 pin connector (connectors, pins, sockets)
RELATED PRODUCTS
CN1566 Electric Motor
oil and gas
- Electric Motor Type: Squirrel Cage Induction Motor
- Full Load Speed: 1189 r/min1189 r/min
- Mounting Designation: F1 or F2
CN3086 Electric Motor for Gas Compression
oil and gas
- Electric Motor Type: Squirrel Cage Induction Motor
- Full Load Speed: 892 r/min892 r/min
- Mounting Designation: F1 or F2
CN3586 Electric Motor for Gas Compression
oil and gas
- Electric Motor Type: Squirrel Cage Induction Motor
- Full Load Speed: 894 rpm
- Mounting Designation: F1 or F2
CN5086 Electric Motor
oil and gas
- Electric Motor Type: Squirrel Cage Induction Motor
- Full Load Speed: 894 r/min894 r/min
- Mounting Designation: F1 or F2
3406C
oil and gas
- Minimum Rating: 217 bkW292 BHP
- Maximum Rating: 359 bkW482 BHP
- Aspiration: Turbocharged Aftercooled
3412
oil and gas
- Minimum Rating: 476 bkW638 BHP
- Maximum Rating: 551 bkW739 BHP
- Aspiration: Turbocharged Aftercooled
3508
oil and gas
- Minimum Rating: 709 bkW950 BHP
- Maximum Rating: 795 bkW1065 BHP
- Aspiration: Turbocharged Aftercooled
3512
oil and gas
- Minimum Rating: 1066 bkW1430 BHP
- Maximum Rating: 1195 bkW1600 BHP
- Aspiration: Turbocharged Aftercooled
3516
oil and gas
- Minimum Rating: 1417 bkW1900 BHP
- Maximum Rating: 1480 bkW1985 BHP
- Aspiration: Turbocharged Aftercooled
