SPECIFICATIONS
- Minimum Rating 1833 ekW2619 kV·A
- Maximum Rating 2660 ekW3325 kV·A
- Speed 1200/1500/1800 rpm
- Aspiration Turbocharged/2-stage aftercooled
- Fuel System Common Rail/EUI™
- Bore 175 mm6.89 in
- Displacement 85 l5167 in³
- Stroke 220 mm8.66 in
- Length 50 Hz - 6782 mm (267 in) / 60 Hz - 6742 mm (265 in)
- Width 50 Hz - 2413 mm (95 in) / 60 Hz - 2125 mm (84 in)
- Height 50 Hz - 2928 (115 in) / 60 Hz - 2916 mm ( 115 in)
- Emissions Available in IMO Tier II/ EPA Marine Tier 2 configurations
- Oil Change Interval 1000 h1000 h
- Lube Oil System Refill 946 l250 gal (US)
- Cooling System Engine 77 l92 gal (US)
- Weight 24312 kg53599 lb
- Generator Set Control MPD 3.0 / Cat® Alarm and Protection System
- Engine Control Dual ADEM™ A4
- Industry oil-and-gas
EQUIPMENT
C175-16 Standard Equipment
- Air Inlet System
- Dual turbochargers
- Corrosion-resistant aftercooler core
- Air cleaners — single or dual element
- Exhaust System
- Dry exhaust manifolds with thermo-laminated heat shields
- Dual turbochargers with water-cooled bearings and thermo-laminated heat shields
- Vertical exhaust outlet
- Flange and exhaust expanders
- Cooling System
- Separate-circuit-aftercooler (SCAC) and jacket water (JW) circuit cooling system
- Gear-driven centrifugal pumps, one for each circuit
- SCAC electronic thermostat, outlet-controlled with aftercooler inlet temperature sensing
- JW electronic thermostat, outlet-controlled with outlet temperature sensing
- Engine oil cooler in JW circuit
- Fuel System
- Cat common rail high-pressure fuel system with electronically controlled unit injectors
- Duplex primary fuel filter with water separator
- Duplex secondary/tertiary fuel filters
- Electric fuel priming pump
- Gear-driven low pressure transfer pump
- Gear-driven high pressure transfer pump
- Double-walled high pressure fuel lines
- Fuel pressure, temperature, and leak detection sensors
- Lubrication System
- Engine-driven, gear-type oil pump
- Integral lube oil cooler
- Front-mounted oil drain lines and valve
- Oil sampling valve
- Filler and dipstick
- Four-canister simplex oil filter
- Prelube pump — electric, air, or custom
- Fumes disposal with crankcase breathers
- Crankcase explosion relief valves
- Engine Control and Protection
- Dual ADEM A4 engine control unit (ECU) for redundancy
- Software monitors engine parameters and performs alarm, derate, and shutdown functions
- Rigid wiring harness
- Marine Power Display 3.0 (MPD 3.0)
- Mounting
- Inner-outer base with vibration isolators
- Generator
- Kato brushless permanent magnet 6P6.6-3200 HR
- 2-bearing, close-coupled arrangement
- 60 Hz, 600V, 0.7 PF
- UL/CSA listed, IP23
- Flywheel and Coupling
- Flywheel housing, SAE No. 00
- Flywheel, SAE No. 00
- ABS certified, non-certified, or custom-coupling and coupling mounting
- Free-standing or close-coupled generator set arrangements
- Starting System
- Turbine air starter or
- Dual electric starting motors or
- Air and electric starting motors (redundant)
- General
- Power distribution box — 24V or custom
- 20A battery charger
- Cat yellow paint
- Offshore oil field sub-base
- Integral spring isolators with limit stop
- Lift provisions on base
- Oil drain extension
- Engine length drip pan with drain
- Torsional dampened driveline couplings
C175-16 Optional Equipment
- Air Inlet System
- Air cleaner service indicator
- Cooling System
- 9 kW, 240V, 60 hz jacket water heater
- Custom jacket water heater
- Fuel System
- Four canister duplex oil filter
- Engine Control and Protection
- Cat Alarm and Protection System
- Communication module PL1000T/E
- Direct-rack control
- Thermocouples
- Metal particle detector
- SOLAS spray shielding
- Mounting
- Custom I-beam base with vibration isolators
- General
- TVA report
- Special tests
- Project-specific installation drawings
- P&ID-electrical drawings
- Spare parts kit
- Barring group
- Engine lifting group
- Custom generators and radiators
360° INTERACTIVE
Exterior
Interior
RELATED PRODUCTS
CN1566 Electric Motor
oil and gas
- Electric Motor Type: Squirrel Cage Induction Motor
- Full Load Speed: 1189 r/min1189 r/min
- Mounting Designation: F1 or F2
CN3086 Electric Motor for Gas Compression
oil and gas
- Electric Motor Type: Squirrel Cage Induction Motor
- Full Load Speed: 892 r/min892 r/min
- Mounting Designation: F1 or F2
CN3586 Electric Motor for Gas Compression
oil and gas
- Electric Motor Type: Squirrel Cage Induction Motor
- Full Load Speed: 894 rpm
- Mounting Designation: F1 or F2
CN5086 Electric Motor
oil and gas
- Electric Motor Type: Squirrel Cage Induction Motor
- Full Load Speed: 894 r/min894 r/min
- Mounting Designation: F1 or F2
3406C
oil and gas
- Minimum Rating: 217 bkW292 BHP
- Maximum Rating: 359 bkW482 BHP
- Aspiration: Turbocharged Aftercooled
3412
oil and gas
- Minimum Rating: 476 bkW638 BHP
- Maximum Rating: 551 bkW739 BHP
- Aspiration: Turbocharged Aftercooled
3508
oil and gas
- Minimum Rating: 709 bkW950 BHP
- Maximum Rating: 795 bkW1065 BHP
- Aspiration: Turbocharged Aftercooled
3512
oil and gas
- Minimum Rating: 1066 bkW1430 BHP
- Maximum Rating: 1195 bkW1600 BHP
- Aspiration: Turbocharged Aftercooled
3516
oil and gas
- Minimum Rating: 1417 bkW1900 BHP
- Maximum Rating: 1480 bkW1985 BHP
- Aspiration: Turbocharged Aftercooled
