NEW / / oil and gas / C13 ACERT™ (Dry Manifold)
C13 ACERT™ (Dry Manifold) oil and ga
C13 ACERT™ (Dry Manifold)
SPECIFICATIONS
EQUIPMENT
RELATED PRODUCTS
C13 ACERT™ (Dry Manifold)
oil and gas
- Minimum Rating 287 bkW385 BHP
- Maximum Rating 387 bkW520 BHP
- Aspiration Turbocharged-Aftercooled
SPECIFICATIONS
- Minimum Rating 287 bkW385 BHP
- Maximum Rating 387 bkW520 BHP
- Aspiration Turbocharged-Aftercooled
- Bore 130 mm5.1 in
- Displacement 12.5 l760 in³
- Stroke 157 mm6.2 in
- Rpm 2100 r/min2100 r/min
- Length 1201 mm47.3 in
- Width 1013 mm39.9 in
- Height 1186 mm46.7 in
- Emissions EPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA
- Rotation From Flywheel End Counterclockwise
- Flywheel And Flywheel Housing SAE 1
- Flywheel Teeth 113
- Lube Oil System Refill 34 l9 gal (US)
- Cooling System 14.4 l3.8 gal (US)
- Governor And Protection Electronic (ADEM™ A3)
- Weight 896 kg1976 lb
- Industry oil-and-gas
EQUIPMENT
C13 ACERT™ (Dry Manifold) Standard Equipment
- Air Inlet System
- Turbocharger, mid-mounted
- Air inlet elbow 90°, 104.5 mm (4.11" OD) hose connection
- Control System
- Electronic governing, PTO speed control
- Programmable ratings
- Cold mode start strategy
- Automatic altitude compensation
- Power compensation for fuel temperature
- Programmable low and high idle and TEL
- Electronic diagnostics and fault logging
- Engine monitoring system — speed, temperature, pressure
- J1939 Broadcast — diagnostic and engine status
- Cooling System
- Thermostats and housing
- Jacket water pump — gear-driven
- Front water pump inlet
- Exhaust System
- Exhaust manifold — dry
- Front turbo exhaust
- Flywheels and Flywheel Housings
- Fuel System
- Electronic unit injector
- Fuel filter — secondary, mid-mount, (LH 2 micron high performance)
- Fuel transfer pump — front
- Fuel priming pump — LH mid-mount
- Fuel fitting — fuel return connection: straight No. 8, 5/8-18
- Lube System
- Crankcase breather
- Oil cooler
- Oil filter — RH
- Oil pan — front sump, 40 L capacity
- Oil filler — LH front
- Oil dipstick — LH front
- Oil pump
- Oil valve sampling — RH rear engine side
- Power Take-Offs
- Crankshaft pulley and damper — 250 mm (9.84 in), 2 grooves 22.3 mm (.87 in) width
- Hydraulic pump drive — SAE A, 11-tooth
- 1.41:1 drive ratio — counterclockwise rotation (45 lb-ft capacity)
- General
- Vibration damper
- Paint — Cat yellow
- Lifting eyes
- Automatic variable timing, electronic
- Electronic installation kit (connectors, pins, sockets)
- Literature
- Mandatory Options
- Flywheel housing or rear PTO
- Throttle position sensor
- Primary filter/water separator
C13 ACERT™ (Dry Manifold) Optional Equipment
- Air Compressor
- Air compressors
- Air chambers
- Air compressor governors
- Air Inlet System
- Air cleaners
- Precleaners
- Air lines
- Air inlet gasket
- Belt-Driven Accessories
- Refrigerant compressor and mounting
- Charging System
- Charging alternators
- Alternator mountings
- Alternator guard
- Alternator accessories
- Cooling System
- Radiator — installed
- Fan drive f/u/w Caterpillar installed radiator
- Fan drive pulleys f/u/w customer-supplied radiators
- Coolant conditioner
- Water lines — pump inlet
- Fan drive mountings
- Fan height instructions
- Fan adapters for suction fans and blower fans
- Suction fans and blower fans
- Coolant level sensor
- Aftercooler lines
- Exhaust System
- Muffler
- Flexible fitting
- Elbows, flange, pipe, clamp
- Straight exhaust adapter
- Fuel System
- Fuel lines for fuel filter
- Fuel cooler
- Fuel fitting — fuel return connection
- Flexible fuel lines
- Instrumentation
- Gauges and instrument panels
- Voltmeters
- Gauge mounting
- Ammeter
- Lube System
- Oil pan
- Oil pan drain
- Oil level gauges
- Oil filter — bypass and remote
- Lubricating oil
- Oil filler
- Fumes disposal
- Mounting System
- Front and rear engine supports
- Structural steel base
- Power Take-Offs
- Crankshaft pulleys
- Crankshaft pulley — stack-on
- Output flange
- Flywheel stub shaft
- Front stub shaft
- Hydraulic pump drive
- Hydraulic pumps — front and rear
- Enclosed clutch
- Clutch support
- Protection System
- Air shutoff
- Air shutoff switch
- Starting System
- Starting System
- Starting aids
- Battery sets — 24 Volt, dry
- Battery cable
- Battery rack
360° INTERACTIVE
SPECIFICATIONS
- Minimum Rating 287 bkW385 BHP
- Maximum Rating 387 bkW520 BHP
- Aspiration Turbocharged-Aftercooled
- Bore 130 mm5.1 in
- Displacement 12.5 l760 in³
- Stroke 157 mm6.2 in
- Rpm 2100 r/min2100 r/min
- Length 1201 mm47.3 in
- Width 1013 mm39.9 in
- Height 1186 mm46.7 in
- Emissions EPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA
- Rotation From Flywheel End Counterclockwise
- Flywheel And Flywheel Housing SAE 1
- Flywheel Teeth 113
- Lube Oil System Refill 34 l9 gal (US)
- Cooling System 14.4 l3.8 gal (US)
- Governor And Protection Electronic (ADEM™ A3)
- Weight 896 kg1976 lb
- Industry oil-and-gas
EQUIPMENT
C13 ACERT™ (Dry Manifold) Standard Equipment
- Air Inlet System
- Turbocharger, mid-mounted
- Air inlet elbow 90°, 104.5 mm (4.11" OD) hose connection
- Control System
- Electronic governing, PTO speed control
- Programmable ratings
- Cold mode start strategy
- Automatic altitude compensation
- Power compensation for fuel temperature
- Programmable low and high idle and TEL
- Electronic diagnostics and fault logging
- Engine monitoring system — speed, temperature, pressure
- J1939 Broadcast — diagnostic and engine status
- Cooling System
- Thermostats and housing
- Jacket water pump — gear-driven
- Front water pump inlet
- Exhaust System
- Exhaust manifold — dry
- Front turbo exhaust
- Flywheels and Flywheel Housings
- Fuel System
- Electronic unit injector
- Fuel filter — secondary, mid-mount, (LH 2 micron high performance)
- Fuel transfer pump — front
- Fuel priming pump — LH mid-mount
- Fuel fitting — fuel return connection: straight No. 8, 5/8-18
- Lube System
- Crankcase breather
- Oil cooler
- Oil filter — RH
- Oil pan — front sump, 40 L capacity
- Oil filler — LH front
- Oil dipstick — LH front
- Oil pump
- Oil valve sampling — RH rear engine side
- Power Take-Offs
- Crankshaft pulley and damper — 250 mm (9.84 in), 2 grooves 22.3 mm (.87 in) width
- Hydraulic pump drive — SAE A, 11-tooth
- 1.41:1 drive ratio — counterclockwise rotation (45 lb-ft capacity)
- General
- Vibration damper
- Paint — Cat yellow
- Lifting eyes
- Automatic variable timing, electronic
- Electronic installation kit (connectors, pins, sockets)
- Literature
- Mandatory Options
- Flywheel housing or rear PTO
- Throttle position sensor
- Primary filter/water separator
C13 ACERT™ (Dry Manifold) Optional Equipment
- Air Compressor
- Air compressors
- Air chambers
- Air compressor governors
- Air Inlet System
- Air cleaners
- Precleaners
- Air lines
- Air inlet gasket
- Belt-Driven Accessories
- Refrigerant compressor and mounting
- Charging System
- Charging alternators
- Alternator mountings
- Alternator guard
- Alternator accessories
- Cooling System
- Radiator — installed
- Fan drive f/u/w Caterpillar installed radiator
- Fan drive pulleys f/u/w customer-supplied radiators
- Coolant conditioner
- Water lines — pump inlet
- Fan drive mountings
- Fan height instructions
- Fan adapters for suction fans and blower fans
- Suction fans and blower fans
- Coolant level sensor
- Aftercooler lines
- Exhaust System
- Muffler
- Flexible fitting
- Elbows, flange, pipe, clamp
- Straight exhaust adapter
- Fuel System
- Fuel lines for fuel filter
- Fuel cooler
- Fuel fitting — fuel return connection
- Flexible fuel lines
- Instrumentation
- Gauges and instrument panels
- Voltmeters
- Gauge mounting
- Ammeter
- Lube System
- Oil pan
- Oil pan drain
- Oil level gauges
- Oil filter — bypass and remote
- Lubricating oil
- Oil filler
- Fumes disposal
- Mounting System
- Front and rear engine supports
- Structural steel base
- Power Take-Offs
- Crankshaft pulleys
- Crankshaft pulley — stack-on
- Output flange
- Flywheel stub shaft
- Front stub shaft
- Hydraulic pump drive
- Hydraulic pumps — front and rear
- Enclosed clutch
- Clutch support
- Protection System
- Air shutoff
- Air shutoff switch
- Starting System
- Starting System
- Starting aids
- Battery sets — 24 Volt, dry
- Battery cable
- Battery rack
RELATED PRODUCTS
-71751c207266b887f0eefdd2cd73b0d8.jpeg)
CN1566 Electric Motor
oil and gas
- Electric Motor Type: Squirrel Cage Induction Motor
- Full Load Speed: 1189 r/min1189 r/min
- Mounting Designation: F1 or F2
CN3086 Electric Motor for Gas Compression
oil and gas
- Electric Motor Type: Squirrel Cage Induction Motor
- Full Load Speed: 892 r/min892 r/min
- Mounting Designation: F1 or F2
CN3586 Electric Motor for Gas Compression
oil and gas
- Electric Motor Type: Squirrel Cage Induction Motor
- Full Load Speed: 894 rpm
- Mounting Designation: F1 or F2
CN5086 Electric Motor
oil and gas
- Electric Motor Type: Squirrel Cage Induction Motor
- Full Load Speed: 894 r/min894 r/min
- Mounting Designation: F1 or F2
3406C
oil and gas
- Minimum Rating: 217 bkW292 BHP
- Maximum Rating: 359 bkW482 BHP
- Aspiration: Turbocharged Aftercooled
3412
oil and gas
- Minimum Rating: 476 bkW638 BHP
- Maximum Rating: 551 bkW739 BHP
- Aspiration: Turbocharged Aftercooled
3508
oil and gas
- Minimum Rating: 709 bkW950 BHP
- Maximum Rating: 795 bkW1065 BHP
- Aspiration: Turbocharged Aftercooled
3512
oil and gas
- Minimum Rating: 1066 bkW1430 BHP
- Maximum Rating: 1195 bkW1600 BHP
- Aspiration: Turbocharged Aftercooled
3516
oil and gas
- Minimum Rating: 1417 bkW1900 BHP
- Maximum Rating: 1480 bkW1985 BHP
- Aspiration: Turbocharged Aftercooled
Articulated trucks
-1.webp)
Dozers
-1-1.png)
Backhoe Loaders
Hydraulic Mining Shovels
ELECTRIC POWER
MARINE POWER SYSTEMS
INDUSTRIAL
OIL AND GAS
