C11 ACERT™ (Dry Manifold)

NEW / / oil and gas / C11 ACERT™ (Dry Manifold)

C11 ACERT™ (Dry Manifold) oil and ga

C11 ACERT™ (Dry Manifold)

SPECIFICATIONS

EQUIPMENT

RELATED PRODUCTS

C11 ACERT™ (Dry Manifold)

oil and gas

Minimum Rating 242 bkW325 BHP
Maximum Rating 336 bkW450 BHP
Aspiration Turbocharged-Aftercooled

Get a quote

OVERVIEW

SPECIFICATIONS

Minimum Rating 242 bkW325 BHP
Maximum Rating 336 bkW450 BHP
Aspiration Turbocharged-Aftercooled
Bore 130 mm5.12 in
Displacement 11.15 l681 in³
Stroke 140 mm5.51 in
Length 1201 mm47.3 in
Width 1057 mm41.6 in
Height 1176 mm46.3 in
Emissions EPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA
Rotation From Flywheel End Counterclockwise
Flywheel And Flywheel Housing SAE 1 or SAE 2
Flywheel Teeth 113 (SAE 1), 138 (SAE 2)
Lube Oil System Refill 34 l9 gal (US)
Governor And Protection Electronic (ADEM™ A3)
Weight 892.22 kg1967 lb
Industry oil-and-gas

EQUIPMENT

C11 ACERT™ (Dry Manifold) Standard Equipment

Air Inlet System
- Turbocharger, mid-mounted
- Air inlet elbow 90°, 104.5 mm (4.11" OD) hose connection

Control System
- Electronic governing, PTO speed control
- Programmable ratings
- Cold mode start strategy
- Automatic altitude compensation
- Power compensation for fuel temperature
- Programmable low and high idle and TEL
- Electronic diagnostics and fault logging
- Engine monitoring system — speed, temperature, pressure
- J1939 Broadcast — diagnostic and engine status

Cooling System
- Thermostats and housing
- Jacket water pump — gear-driven
- Front water pump inlet

Exhaust System
- Exhaust manifold — dry
- Front turbo exhaust

Flywheels and Flywheel Housings
- See Mandatory Options

Fuel System
- Electronic unit injector
- Fuel filter — secondary, mid-mount, (LH 2 micron high performance)
- Fuel transfer pump — front
- Fuel priming pump — LH mid-mount

Lube System
- Crankcase breather
- Oil cooler
- Oil filter — RH
- Oil pan — front sump, 40 L capacity
- Oil filler — LH front
- Oil dipstick — LH mid-mount
- Oil pump
- Oil valve sampling — on oil filter base

Power Take-Offs
- Crankshaft pulley and damper — 250 mm (9.84 in), 2 grooves 22.3 mm (.87 in) width
- Hydraulic pump drive — SAE A, 11 tooth
- 1.41:1 drive ratio — counterclockwise rotation (45 lb-ft capacity)

General
- Vibration damper
- Paint — Cat yellow
- Lifting eyes
- Automatic variable timing, electronic
- Electronic installation kit (connectors, pins, sockets)
- Literature

Mandatory Options
- Flywheel housing or rear PTO
- Throttle position sensor
- Primary filter/water separator

C11 ACERT™ (Dry Manifold) Optional Equipment

Air Compressor
- Expansion chamber
- Governors
- Fittings

Air Inlet System
- Air cleaners
- Precleaners
- Turbo air inlet
- Air lines

Belt-Driven Accessories
- Refrigerant compressor and mounting

Charging System
- Charging alternators
- Alternator mountings
- Alternator guard
- Alternator accessories

Control System
- Connection

Cooling System
- Radiator — installed
- Fan drive f/u/w Caterpillar installed radiator
- Fan drive pulleys f/u/w customer-supplied radiators
- Coolant conditioner
- Water lines — pump inlet
- Fan drive mountings
- Fan height instructions
- Fan adapters for suction fans
- Fan adapters for blower fans
- Suction fans
- Blower fans
- Coolant level sensor
- Aftercooler lines

Exhaust System
- Muffler
- Flexible fitting
- Elbows
- Straight exhaust adapter
- Flange
- Pipe
- Rain cap
- Clamp

Fuel System
- Fuel lines
- Fuel cooler
- Fuel fitting — fuel return and supply connections
- Flexible fuel lines

Instrumentation
- Gauges and instrument panels
- Voltmeters
- Gauge mounting
- Ammeter

Lube System
- Oil pan
- Oil pan drain
- Oil level gauges
- Oil filter — bypass
- Oil filter — remote
- Lubricating oil
- Oil filler
- Fumes disposal

Mounting System
- Front and rear engine supports
- Structural steel base

Power Take-Offs
- Crankshaft pulleys
- Crankshaft pulley — stack-on
- Output flange
- Flywheel stub shaft
- Front stub shaft
- Hydraulic pump drive
- Hydraulic pumps — front
- Hydraulic pumps — rear
- Enclosed Clutch
- Clutch Support

Protection System
- Air shutoff
- Air shutoff switch

Starting System
- Electric starting motors — 12 Volt, 24 Volt
- Starting aids
- Battery sets — 24 Volt, dry
- Battery cable
- Battery rack

Transmission Arrangement
- Transmission cooler

360° INTERACTIVE

SPECIFICATIONS

Minimum Rating 242 bkW325 BHP
Maximum Rating 336 bkW450 BHP
Aspiration Turbocharged-Aftercooled
Bore 130 mm5.12 in
Displacement 11.15 l681 in³
Stroke 140 mm5.51 in
Length 1201 mm47.3 in
Width 1057 mm41.6 in
Height 1176 mm46.3 in
Emissions EPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA
Rotation From Flywheel End Counterclockwise
Flywheel And Flywheel Housing SAE 1 or SAE 2
Flywheel Teeth 113 (SAE 1), 138 (SAE 2)
Lube Oil System Refill 34 l9 gal (US)
Governor And Protection Electronic (ADEM™ A3)
Weight 892.22 kg1967 lb
Industry oil-and-gas

EQUIPMENT

C11 ACERT™ (Dry Manifold) Standard Equipment

Air Inlet System
- Turbocharger, mid-mounted
- Air inlet elbow 90°, 104.5 mm (4.11" OD) hose connection

Control System
- Electronic governing, PTO speed control
- Programmable ratings
- Cold mode start strategy
- Automatic altitude compensation
- Power compensation for fuel temperature
- Programmable low and high idle and TEL
- Electronic diagnostics and fault logging
- Engine monitoring system — speed, temperature, pressure
- J1939 Broadcast — diagnostic and engine status

Cooling System
- Thermostats and housing
- Jacket water pump — gear-driven
- Front water pump inlet

Exhaust System
- Exhaust manifold — dry
- Front turbo exhaust

Flywheels and Flywheel Housings
- See Mandatory Options

Fuel System
- Electronic unit injector
- Fuel filter — secondary, mid-mount, (LH 2 micron high performance)
- Fuel transfer pump — front
- Fuel priming pump — LH mid-mount

Lube System
- Crankcase breather
- Oil cooler
- Oil filter — RH
- Oil pan — front sump, 40 L capacity
- Oil filler — LH front
- Oil dipstick — LH mid-mount
- Oil pump
- Oil valve sampling — on oil filter base

Power Take-Offs
- Crankshaft pulley and damper — 250 mm (9.84 in), 2 grooves 22.3 mm (.87 in) width
- Hydraulic pump drive — SAE A, 11 tooth
- 1.41:1 drive ratio — counterclockwise rotation (45 lb-ft capacity)

General
- Vibration damper
- Paint — Cat yellow
- Lifting eyes
- Automatic variable timing, electronic
- Electronic installation kit (connectors, pins, sockets)
- Literature

Mandatory Options
- Flywheel housing or rear PTO
- Throttle position sensor
- Primary filter/water separator

C11 ACERT™ (Dry Manifold) Optional Equipment

Air Compressor
- Expansion chamber
- Governors
- Fittings

Air Inlet System
- Air cleaners
- Precleaners
- Turbo air inlet
- Air lines

Belt-Driven Accessories
- Refrigerant compressor and mounting

Charging System
- Charging alternators
- Alternator mountings
- Alternator guard
- Alternator accessories

Control System
- Connection

Cooling System
- Radiator — installed
- Fan drive f/u/w Caterpillar installed radiator
- Fan drive pulleys f/u/w customer-supplied radiators
- Coolant conditioner
- Water lines — pump inlet
- Fan drive mountings
- Fan height instructions
- Fan adapters for suction fans
- Fan adapters for blower fans
- Suction fans
- Blower fans
- Coolant level sensor
- Aftercooler lines

Exhaust System
- Muffler
- Flexible fitting
- Elbows
- Straight exhaust adapter
- Flange
- Pipe
- Rain cap
- Clamp

Fuel System
- Fuel lines
- Fuel cooler
- Fuel fitting — fuel return and supply connections
- Flexible fuel lines

Instrumentation
- Gauges and instrument panels
- Voltmeters
- Gauge mounting
- Ammeter

Lube System
- Oil pan
- Oil pan drain
- Oil level gauges
- Oil filter — bypass
- Oil filter — remote
- Lubricating oil
- Oil filler
- Fumes disposal

Mounting System
- Front and rear engine supports
- Structural steel base

Power Take-Offs
- Crankshaft pulleys
- Crankshaft pulley — stack-on
- Output flange
- Flywheel stub shaft
- Front stub shaft
- Hydraulic pump drive
- Hydraulic pumps — front
- Hydraulic pumps — rear
- Enclosed Clutch
- Clutch Support

Protection System
- Air shutoff
- Air shutoff switch

Starting System
- Electric starting motors — 12 Volt, 24 Volt
- Starting aids
- Battery sets — 24 Volt, dry
- Battery cable
- Battery rack

Transmission Arrangement
- Transmission cooler

RELATED PRODUCTS

CN1566 Electric Motor

oil and gas

Electric Motor Type: Squirrel Cage Induction Motor
Full Load Speed: 1189 r/min1189 r/min
Mounting Designation: F1 or F2

Get a quote

CN3086 Electric Motor for Gas Compression

oil and gas

Electric Motor Type: Squirrel Cage Induction Motor
Full Load Speed: 892 r/min892 r/min
Mounting Designation: F1 or F2

Get a quote

CN3586 Electric Motor for Gas Compression

oil and gas

Electric Motor Type: Squirrel Cage Induction Motor
Full Load Speed: 894 rpm
Mounting Designation: F1 or F2

Get a quote

CN5086 Electric Motor

oil and gas

Electric Motor Type: Squirrel Cage Induction Motor
Full Load Speed: 894 r/min894 r/min
Mounting Designation: F1 or F2

Get a quote

3406C

oil and gas

Minimum Rating: 217 bkW292 BHP
Maximum Rating: 359 bkW482 BHP
Aspiration: Turbocharged Aftercooled

Get a quote

3412

oil and gas

Minimum Rating: 476 bkW638 BHP
Maximum Rating: 551 bkW739 BHP
Aspiration: Turbocharged Aftercooled

Get a quote

3508

oil and gas

Minimum Rating: 709 bkW950 BHP
Maximum Rating: 795 bkW1065 BHP
Aspiration: Turbocharged Aftercooled

Get a quote

3512

oil and gas

Minimum Rating: 1066 bkW1430 BHP
Maximum Rating: 1195 bkW1600 BHP
Aspiration: Turbocharged Aftercooled

Get a quote

3516

oil and gas

Minimum Rating: 1417 bkW1900 BHP
Maximum Rating: 1480 bkW1985 BHP
Aspiration: Turbocharged Aftercooled

Get a quote