3516C (HD) CI/D2 Hazardous Location

NEW / / oil and gas / 3516C (HD) CI/D2 Hazardous Location

3516C (HD) CI/D2 Hazardous Location oil and ga

3516C (HD) CI/D2 Hazardous Location

SPECIFICATIONS

EQUIPMENT

360° INTERACTIVE

RELATED PRODUCTS

3516C (HD) CI/D2 Hazardous Location

oil and gas

Minimum Rating 2100 ekW2625 kV·A
Maximum Rating 2100 ekW2625 kV·A
Aspiration Dual Turbocharged-Aftercooled

Get a quote

OVERVIEW

SPECIFICATIONS

Minimum Rating 2100 ekW2625 kV·A
Maximum Rating 2100 ekW2625 kV·A
Aspiration Dual Turbocharged-Aftercooled
Fuel System EUI
Bore 170 mm6.7 in
Displacement 78 l4760 in³
Stroke 215 mm8.5 in
Length 6705 mm264 in
Width 1986 mm78 in
Height 2535 mm100 in
Emissions EPA Tier 2, IMO Tier II
Lube Oil System Refill 405 l107 gal (US)
Cooling System Engine 234.7 l62 gal (US)
Weight 17500 kg38581 lb
Engine Control ADEM A4
Industry oil-and-gas

EQUIPMENT

3516C (HD) CI/D2 Hazardous Location Standard Equipment

AIR INLET SYSTEM
- Aftercooler core, corrosion resistant (air side)
- Air cleaner, regular duty with service indicators
- Dual turbochargers, rear mounted

CONTROL SYSTEM
- Dual Caterpillar A4 electronic engine control with electronic unit injector fuel system and rigid wiring harness.
- 24 VDC (less than 10A) to be provided by customer at Power Distribution Panel to power engine electrical system.

COOLING SYSTEM
- Jacket water (JW) engine cooling and two-stage jacket water/separate circuit (SCAC) charge air cooling
- To ensure compliance in use, radiators or heat exchangers must be capable of rejecting sufficient heat to allow proper engine operation at worst site conditions.
- The radiator or heat exchanger must supply 48C (118 F)
- SCAC cooling water to the aftercooler inlet of at least 200 gal/min at ambient temperature of 30C and at site conditions (including altitude considerations)

EXHAUST SYSTEM
- Dry gas-tight exhaust manifolds with heat shields, dual turbochargers with water-cooled bearings and heat shields.
- Exhaust outlet: 305 mm (12 in) round flanged outlet, vertical orientation

FLYWHEELS & FLYWHEEL HOUSINGS
- Flywheel, SAE No. 00, 183 teeth Flywheel housing, SAE No. 00
- Flywheel housing, SAE No. 00
- SAE standard rotation

FUEL SYSTEM
- Duplex Fuel filter, LH service. Simplex fuel filter, RH service
- Fuel transfer pump
- Fuel priming pump, RH
- Electronically Controlled Unit Injectors
- Customer connection located at lower right front of engine
- SOLAS shielding

INSTRUMENTATION
- Engine mounted instrument panel with four position switch, over speed shutdown notification light, emergency stop notification light, graphical display unit for analog or digital display of: oil and fuel pressure, oil and fuel filter differential, system DC voltage, exhaust and water temperature, air inlet restriction, service meter, engine speed, fuel consumption (total and instantaneous)

LUBE SYSTEM
- Top mounted crankcase breather, RH oil filter, RH oil filler, gear type oil pump, deep sump oil pan, recommended use of Caterpillar Diesel Engine Oil 10W30 or 15W40

MOUNTING SYSTEM
- Mounting rails and isolation system based on customer request

ELECTRICAL SYSTEM
- MCS certified Class I / Divison 2
- Low Smoke Zero Halogen Wiring Harness

PROTECTION SYSTEM
- A-III Electronic Monitoring System provides customer programmable engine de-ration strategies to protect against adverse operating conditions
- Emergency stop push button (located in Electronic Instrument Panel) Safety shutoff protection for oil pressure and water temperature, over speed protection

HAZARDOUS LOCATION
- Only electrical system is hazardous environment certified
- NEC 500 Class I Division 2 for gas groups C and D
- Temperature class is T3 for ambient temperatures from -10 C to 50 C
- Class I/ Division 2 CMPD

GENERATOR AND GENERATOR ATTACHMENTS
- Class I / Division 2 designed to customer's specifications
- Insulation for harsh environment protection

360° INTERACTIVE

Exterior

SPECIFICATIONS

Minimum Rating 2100 ekW2625 kV·A
Maximum Rating 2100 ekW2625 kV·A
Aspiration Dual Turbocharged-Aftercooled
Fuel System EUI
Bore 170 mm6.7 in
Displacement 78 l4760 in³
Stroke 215 mm8.5 in
Length 6705 mm264 in
Width 1986 mm78 in
Height 2535 mm100 in
Emissions EPA Tier 2, IMO Tier II
Lube Oil System Refill 405 l107 gal (US)
Cooling System Engine 234.7 l62 gal (US)
Weight 17500 kg38581 lb
Engine Control ADEM A4
Industry oil-and-gas

EQUIPMENT

3516C (HD) CI/D2 Hazardous Location Standard Equipment

AIR INLET SYSTEM
- Aftercooler core, corrosion resistant (air side)
- Air cleaner, regular duty with service indicators
- Dual turbochargers, rear mounted

CONTROL SYSTEM
- Dual Caterpillar A4 electronic engine control with electronic unit injector fuel system and rigid wiring harness.
- 24 VDC (less than 10A) to be provided by customer at Power Distribution Panel to power engine electrical system.

COOLING SYSTEM
- Jacket water (JW) engine cooling and two-stage jacket water/separate circuit (SCAC) charge air cooling
- To ensure compliance in use, radiators or heat exchangers must be capable of rejecting sufficient heat to allow proper engine operation at worst site conditions.
- The radiator or heat exchanger must supply 48C (118 F)
- SCAC cooling water to the aftercooler inlet of at least 200 gal/min at ambient temperature of 30C and at site conditions (including altitude considerations)

EXHAUST SYSTEM
- Dry gas-tight exhaust manifolds with heat shields, dual turbochargers with water-cooled bearings and heat shields.
- Exhaust outlet: 305 mm (12 in) round flanged outlet, vertical orientation

FLYWHEELS & FLYWHEEL HOUSINGS
- Flywheel, SAE No. 00, 183 teeth Flywheel housing, SAE No. 00
- Flywheel housing, SAE No. 00
- SAE standard rotation

FUEL SYSTEM
- Duplex Fuel filter, LH service. Simplex fuel filter, RH service
- Fuel transfer pump
- Fuel priming pump, RH
- Electronically Controlled Unit Injectors
- Customer connection located at lower right front of engine
- SOLAS shielding

INSTRUMENTATION
- Engine mounted instrument panel with four position switch, over speed shutdown notification light, emergency stop notification light, graphical display unit for analog or digital display of: oil and fuel pressure, oil and fuel filter differential, system DC voltage, exhaust and water temperature, air inlet restriction, service meter, engine speed, fuel consumption (total and instantaneous)

LUBE SYSTEM
- Top mounted crankcase breather, RH oil filter, RH oil filler, gear type oil pump, deep sump oil pan, recommended use of Caterpillar Diesel Engine Oil 10W30 or 15W40

MOUNTING SYSTEM
- Mounting rails and isolation system based on customer request

ELECTRICAL SYSTEM
- MCS certified Class I / Divison 2
- Low Smoke Zero Halogen Wiring Harness

PROTECTION SYSTEM
- A-III Electronic Monitoring System provides customer programmable engine de-ration strategies to protect against adverse operating conditions
- Emergency stop push button (located in Electronic Instrument Panel) Safety shutoff protection for oil pressure and water temperature, over speed protection

HAZARDOUS LOCATION
- Only electrical system is hazardous environment certified
- NEC 500 Class I Division 2 for gas groups C and D
- Temperature class is T3 for ambient temperatures from -10 C to 50 C
- Class I/ Division 2 CMPD

GENERATOR AND GENERATOR ATTACHMENTS
- Class I / Division 2 designed to customer's specifications
- Insulation for harsh environment protection

360° INTERACTIVE

Exterior

Interior

RELATED PRODUCTS

CN1566 Electric Motor

oil and gas

Electric Motor Type: Squirrel Cage Induction Motor
Full Load Speed: 1189 r/min1189 r/min
Mounting Designation: F1 or F2

Get a quote

CN3086 Electric Motor for Gas Compression

oil and gas

Electric Motor Type: Squirrel Cage Induction Motor
Full Load Speed: 892 r/min892 r/min
Mounting Designation: F1 or F2

Get a quote

CN3586 Electric Motor for Gas Compression

oil and gas

Electric Motor Type: Squirrel Cage Induction Motor
Full Load Speed: 894 rpm
Mounting Designation: F1 or F2

Get a quote

CN5086 Electric Motor

oil and gas

Electric Motor Type: Squirrel Cage Induction Motor
Full Load Speed: 894 r/min894 r/min
Mounting Designation: F1 or F2

Get a quote

3406C

oil and gas

Minimum Rating: 217 bkW292 BHP
Maximum Rating: 359 bkW482 BHP
Aspiration: Turbocharged Aftercooled

Get a quote

3412

oil and gas

Minimum Rating: 476 bkW638 BHP
Maximum Rating: 551 bkW739 BHP
Aspiration: Turbocharged Aftercooled

Get a quote

3508

oil and gas

Minimum Rating: 709 bkW950 BHP
Maximum Rating: 795 bkW1065 BHP
Aspiration: Turbocharged Aftercooled

Get a quote

3512

oil and gas

Minimum Rating: 1066 bkW1430 BHP
Maximum Rating: 1195 bkW1600 BHP
Aspiration: Turbocharged Aftercooled

Get a quote

3516

oil and gas

Minimum Rating: 1417 bkW1900 BHP
Maximum Rating: 1480 bkW1985 BHP
Aspiration: Turbocharged Aftercooled

Get a quote