C13 ACERT™ (Dry Manifold) Standard Equipment

• Air Inlet System
  • Turbocharger, mid-mounted
  • Air inlet elbow 90°, 104.5 mm (4.11" OD) hose connection

• Control System
  • Electronic governing, PTO speed control
  • Programmable ratings
  • Cold mode start strategy
  • Automatic altitude compensation
  • Power compensation for fuel temperature
  • Programmable low and high idle and TEL
  • Electronic diagnostics and fault logging
  • Engine monitoring system — speed, temperature, pressure
  • J1939 Broadcast — diagnostic and engine status

• Cooling System
  • Thermostats and housing
  • Jacket water pump — gear-driven
  • Front water pump inlet

• Exhaust System
  • Exhaust manifold — dry
  • Front turbo exhaust

• Flywheels and Flywheel Housings
  • See Mandatory Options

• Fuel System
  • Electronic unit injector
  • Fuel filter — secondary, mid-mount, (LH 2 micron high performance)
  • Fuel transfer pump — front
  • Fuel priming pump — LH mid-mount
  • Fuel fitting — fuel return connection: straight No. 8, 5/8-18

• Lube System
  • Crankcase breather
  • Oil cooler
  • Oil filter — RH
  • Oil pan — front sump, 40 L capacity
  • Oil filler — LH front
  • Oil dipstick — LH front
  • Oil pump
  • Oil valve sampling — RH rear engine side

• Power Take-Offs
  • Crankshaft pulley and damper — 250 mm (9.84 in), 2 grooves 22.3 mm (.87 in) width
  • Hydraulic pump drive — SAE A, 11-tooth
  • 1.41:1 drive ratio — counterclockwise rotation (45 lb-ft capacity)

• General
  • Vibration damper
  • Paint — Cat yellow
  • Lifting eyes
  • Automatic variable timing, electronic
  • Electronic installation kit (connectors, pins, sockets)
  • Literature

• Mandatory Options
  • Flywheel housing or rear PTO
  • Throttle position sensor
  • Primary filter/water separator

C13 ACERT™ (Dry Manifold) Optional Equipment

• Air Compressor
  • Air compressors
  • Air chambers
  • Air compressor governors

• Air Inlet System
  • Air cleaners
  • Precleaners
  • Air lines
  • Air inlet gasket

• Belt-Driven Accessories
  • Refrigerant compressor and mounting

• Charging System
  • Charging alternators
  • Alternator mountings
  • Alternator guard
  • Alternator accessories

• Control System
  • Connection

• Cooling System
  • Radiator — installed
  • Fan drive f/u/w Caterpillar installed radiator
  • Fan drive pulleys f/u/w customer-supplied radiators
  • Coolant conditioner
  • Water lines — pump inlet
  • Fan drive mountings
  • Fan height instructions
  • Fan adapters for suction fans and blower fans
  • Suction fans and blower fans
  • Coolant level sensor
  • Aftercooler lines

• Exhaust System
  • Muffler
  • Flexible fitting
  • Elbows, flange, pipe, clamp
  • Straight exhaust adapter

• Fuel System
  • Fuel lines for fuel filter
  • Fuel cooler
  • Fuel fitting — fuel return connection
  • Flexible fuel lines

• Instrumentation
  • Gauges and instrument panels
  • Voltmeters
  • Gauge mounting
  • Ammeter

• Lube System
  • Oil pan
  • Oil pan drain
  • Oil level gauges
  • Oil filter — bypass and remote
  • Lubricating oil
  • Oil filler
  • Fumes disposal

• Mounting System
  • Front and rear engine supports
  • Structural steel base

• Power Take-Offs
  • Crankshaft pulleys
  • Crankshaft pulley — stack-on
  • Output flange
  • Flywheel stub shaft
  • Front stub shaft
  • Hydraulic pump drive
  • Hydraulic pumps — front and rear
  • Enclosed clutch
  • Clutch support

• Protection System
  • Air shutoff
  • Air shutoff switch

• Starting System
  • Starting System
  • Starting aids
  • Battery sets — 24 Volt, dry
  • Battery cable
  • Battery rack

• Transmission Arrangement
  • Transmission cooler